1-32zone Conventional fire alarm fire detection control panel
Model: AW-CFP2166
Introduce
1. Strictly in accordance with the EN54 part 2&4 standard.
2. Modularized design with extendable zones from 1 to 32 zones.
3. With two-level control modes by lock
4. 24VDC & 5VDC power supply outputs.
5. FIRE & FAULT signal outputs.
6. Owns 2 general sounders outputs.
7. Each zone has 1 circuit detectors input .
8. Each zone can be disable by a button.
9. RESET button available
10.SILENCE button to stop BUZZER and SOUNDERS.
11. EVACUATE button to start a manual fire alarm immediately.
12.Low-battery level protection function, i.e., battery voltage lower than 21VDC, battery will be cut off automatically until the mains power is on.
13.GSM module for fire alarm by SMS is optional.
14 Economic, user-friendly & convenient maintenance.
Packaging & Shipping
As the pics shows:
| ITEM |
1Zone panel |
2Zone panel |
4-8 Zone panel |
12-32 Zone panel |
| Model No. |
AW-CFP2166-01 |
AW-CFP2166-02 |
AW-CFP2166-04-8 |
AW-CFP2166-12-32 |
| Power specification |
|
| Mains supply voltage |
110VAC or 240VAC |
| Internal power supply |
27.2VDC |
| Total output current limited |
500mA @ 240VAC |
500mA @ 240VAC |
3A @ 240VAC |
3A @ 240VAC |
| Main supply monitor for fault |
Yes |
| Battery protection for low voltage |
Yes |
| Batteries (default configuration) |
12V2AH*2 |
| Detector circuit specification |
|
| Number of circuit |
1 |
2 |
4-16 |
4-32 |
| Line fault monitor for open circuit |
Yes |
| Line fault monitor for short circuit |
Yes |
| Line fault monitor for detector removal |
Yes, if End of Line Monitor Unit fitted in place of End of Line Resistor |
| End of Line device |
6.8k Ω,5% tolerance, 0.25W (colour code-blue,grey,red,gold) |
| Detector continuity diodes |
Silicon 1N4001 or Schottky type (required if End of Line Monitor Unit fitted to give Detector Removal Fault) |
| Call point resistor value |
470 to 680 Ω, 0.225 or 0.5 watt |
| Maximum number of smoke/heat detectors per zone |
20 (based on a total detector current of 2mA, each detector consuming 100μA).Note: if End of Line Monitor Unit is fitted, for correct operation maxmum voltage drop must not exceed 12 volts. |
| Maximum number of manual call points per zone |
No limit |
| Sounder circuit specification |
|
| Number of general circuits |
2 |
| End of line resistor value |
6.8k Ω,5% tolerance, 0.25W (colour code-blue,grey,red,gold) |
| Line fault monitor for open circuit |
Yes |
| Line fault monitor for short circuit |
Yes |
| Outputs fused AT |
400mA |
| Maximum number of bells @ 20mA of each sounder output |
20 |
| Fuses |
|
| Battery fuse |
1.5A F 20mm |
| Sounder outputs |
500mA F 20mm |
| Fire and fault output |
|
| Output type |
NC and NO relay |
| Maximum current |
100mA |
| Connection block |
|
| Largest acceptable conductor size |
2.5mm2 |
| Smallest acceptable conductor size |
0.75mm2 |
| Size and weight |
|
|
| Dimensions(mm) |
272*200*70mm |
320*231*90mm |
395X502X124 |
362X565X124 |
| Weight (without batteries) |
4kg |
5kg |
7kg |
8kg |
| Weight (with batteries) |
5.8kg |
6.8kg |
9.6kg |
12.5kg |
Company Information
Asenware,manufacturer of fire alarm and fire suppression system since 2005.
Our headquarter is in London, UK, with factory Shenzhen, China.
We keep our best service for our customers, and have a rich experienced engineer team to design and install
for overseas project.
Product range
Addressable fire alarm system
Conventional fire alarm system (2166 series)
FM200 gas suppression system (2159 series)
Fire pump
Fire hose/ hose reel and cabinet
ABC powder/ CO2 fire extinguisher
Emergency light system
Certificates
){kind=link}
){kind=link}